Fence Post Depth Calculator
Find out exactly how deep your fence posts need to be, how much concrete to use, and the total post length required — based on fence height, soil type, and post size. Built on industry-standard guidelines.
Fence Post Specifications
Enter your fence height, post size, soil type, and number of posts
The visible height of the fence above ground level
Hole diameter should be 2–3× the post width. Auto-set to 2.5× if left default.
Adds a soil multiplier to the base 1/3 rule depth.
Extra depth below the frost line — 150mm is standard for UK; increase in colder climates
Concrete is recommended for all wooden posts over 1.2m
Post Installation Guide
Depth, concrete, and total post length
Enter your fence height and specifications above, then click Calculate Post Depths to get your complete installation guide.
If you want to explore this further, the suspended ceiling calculator is a good next step.
Everything to Know About the Fence Post Depth Calculator Practical Guide
What this calculator does
Good decisions start with good numbers. The Fence Post Depth Calculator helps you gather those numbers for fence post depth without spreadsheets, formulas or specialist software, and the result is ready to note down immediately.
Who it helps
Self-builders, builders and contractors and quantity surveyors often turn to calculators like this one. Matching your own situation to the inputs takes only a moment, and you can repeat the process whenever your circumstances change. Many people open this page while checking a quote from a contractor, comparing two design options and planning a loft or extension. Having the answer ready keeps the rest of the task on track.
Getting accurate results
A few habits make fence post depth far more reliable. First, keep all measurements in one unit. Second, check supplier pack sizes. Finally, run your numbers twice with slightly different assumptions so you can see a range of possible outcomes rather than relying on a single figure.
Mistakes to avoid
Some mistakes appear again and again when people calculate fence post depth. Typical examples are rounding quantities down and using nominal sizes instead of actual sizes. Spotting these early keeps your result trustworthy and saves time later.
Reading your result
Results are most useful when you understand what drives them. Experiment with depth and fence in turn, and you will quickly see which one matters most for fence post depth. Clear inputs lead to clear answers, so take a few extra seconds to read each label on the calculator before typing. Bookmark this page so the Fence Post Depth Calculator is always one tap away when you need it again. The layout is designed for readability, so you can use the Fence Post Depth Calculator comfortably on a small screen while on the move. Keeping a short note of each result makes it easy to compare options and explain your reasoning to others.
A note on accuracy
This Fence Post Depth Calculator gives planning estimates only. Confirm final quantities on site and follow building regulations and professional advice for structural or safety-critical work.
Fence Post Depth Reference Chart
Standard fence post depths and total post lengths for common fence heights in firm average soil. Always add extra depth for soft, clay, or exposed sites.
| Fence Height | Min Hole Depth | Total Post Length | Post Size (typical) | Use Case |
|---|---|---|---|---|
| 0.6m (2ft) | 300mm | 0.9m (3ft) | 75×75mm | Low border, decorative |
| 0.9m (3ft) | 450mm | 1.35m (4.5ft) | 75×75mm | Garden border fence |
| 1.2m (4ft) | 500mm | 1.7m (5.5ft) | 75×75mm | Low privacy, pool fence |
| 1.5m (5ft) | 600mm | 2.1m (7ft) | 100×100mm | Standard garden privacy |
| 1.8m (6ft) | 700mm | 2.5m (8ft) | 100×100mm | Full privacy fence (most common) |
| 2.1m (7ft) | 800mm | 2.9m (9.5ft) | 100×100mm | High security / acoustic |
| 2.4m (8ft) | 900mm | 3.3m (11ft) | 125×125mm | Commercial / industrial |
The Rule of Thumb: One-Third in the Ground
The standard rule is to bury one-third of the post’s above-ground height. A 6 ft fence therefore needs 2 ft of post in the ground, so you buy an 8 ft post: 6 ft above ground and 2 ft buried. Some guides phrase the rule as one-third of the total post length instead, which for an 8 ft post gives 2 ft 8 in of depth; the two rules agree closely, and the above-ground version is the one most fence installers use. In metric terms, a 1.8 m fence needs 600 mm of depth and a 2.4 m post. Never go shallower than 450 mm, even for a low fence, because a shallow post will lean within a year or two.
Annotated Cross-Section: Post, Depth and Height
Picture the post in cross-section, from the top down. At the top is the post cap, which keeps rain out of the end grain. Below it is the above-ground height: the part of the fence you can see, for example 1.8 m. At ground level is the most vulnerable point, where the post meets the soil and the concrete; this is where rot starts, so the post should be pressure-treated and the concrete should slope away from the post so water runs off. Below ground level is the buried depth, for example 600 mm, set in concrete. Under the post is a 50 mm bed of gravel or hardcore for drainage, which stops the end of the post sitting in standing water. The concrete collar should finish slightly above ground level and slope away from the post.
Depth Table: Fence Height to Post Length
This table uses the one-third rule on the above-ground height. Buy the post length shown, and bury the depth shown.
| Fence height above ground | Depth to bury | Post length to buy |
|---|---|---|
| 3 ft (0.9 m) | 1 ft (300 mm) | 4 ft (1.2 m) |
| 4 ft (1.2 m) | 1 ft 4 in (400 mm) | 5 ft 4 in (1.6 m) |
| 5 ft (1.5 m) | 1 ft 8 in (500 mm) | 6 ft 8 in (2.0 m) |
| 6 ft (1.8 m) | 2 ft (600 mm) | 8 ft (2.4 m) |
| 7 ft (2.1 m) | 2 ft 4 in (700 mm) | 9 ft 4 in (2.8 m) |
| 8 ft (2.4 m) | 2 ft 8 in (800 mm) | 10 ft 8 in (3.2 m) |
Planning Tips: Spacing, Frost Line and Wind
Space posts 1.8 m (6 ft) apart, which matches the standard length of fence panels and gravel boards; wider spacing saves posts but lets panels sag and catch the wind. In the UK, 600 mm is the usual minimum depth for a 1.8 m fence, and it also clears the frost line in most of the country, so frost heave will not lift the post. In the United States the frost line varies by state, from a few inches in Florida to about 60 inches in Minnesota, so check your local building code and bury the post below the frost line wherever you are. A solid fence acts like a sail: in an exposed or windy site, go deeper, use a wider hole, and consider a fence with gaps, such as hit-and-miss boarding, which lets the wind through.
Full Project Estimator: A 30 m Run
Take a 30 m run of 1.8 m feather-edge fencing with posts every 1.8 m. That is 30 ÷ 1.8 = 16.7 bays, rounded up to 17 bays, which needs 18 posts. Each bay takes 13 feather-edge boards 150 mm wide with a 10 mm overlap, so 17 × 13 = 221 boards. Each bay also needs 2 arris rails and 1 gravel board, so 34 rails and 17 gravel boards, plus post caps and fixings. Each post hole is 300 mm across and 600 mm deep, which is 42.4 litres of concrete, or 5 bags of 20 kg Postcrete per post, so 18 posts need 90 bags. Add 10% contingency to every quantity, because boards split, posts vary in length and holes end up bigger than planned.
Concrete Bag Counts by Hole Size
A 20 kg bag of Postcrete makes about 10 litres of concrete, and a 50 lb bag of concrete mix makes about 0.375 cubic feet. Round every figure up to whole bags.
| Hole size (diameter × depth) | Concrete needed | Bags per post |
|---|---|---|
| 300 mm × 600 mm | 42.4 litres | 5 bags of 20 kg Postcrete |
| 300 mm × 450 mm | 31.8 litres | 4 bags of 20 kg Postcrete |
| 12 in × 2 ft | 1.57 cu ft | 5 bags of 50 lb mix |
| 10 in × 2 ft | 1.09 cu ft | 3 bags of 50 lb mix |
Frequently Asked Questions
How deep should a fence post be? One-third of the above-ground height: 2 ft for a 6 ft fence, or 600 mm for a 1.8 m fence. How long a post do I need for a 6 ft fence? 8 ft, or 2.4 m: 6 ft above ground and 2 ft buried. How many bags of concrete per post? 5 bags of 20 kg Postcrete for a 300 mm by 600 mm hole. How far apart should fence posts be? 1.8 m, or 6 ft, which matches standard panels and gravel boards. Do I need to go below the frost line? Yes: in the UK 600 mm is usually enough, and in the US the frost line varies by state, up to about 60 inches in Minnesota. Why do fence posts lean? Usually because the hole was too shallow, the concrete was too thin, or the post rotted at ground level.
Related: work out desk height.
Fence Post Depth FAQ
Everything you need to know about setting fence posts correctly, from hole depth to concrete quantities and soil considerations.
The standard rule is to bury fence posts to a depth of one-third of the total post length, or one-third of the fence height plus 150mm (6 inches) for a frost buffer. For example, a 6ft (1.8m) fence typically requires posts set at least 600mm (2ft) deep in firm soil, and 750–900mm (2.5–3ft) in soft or clay-heavy ground. Gate posts and corner posts should always be set deeper than standard line posts.
The volume of concrete needed per post hole is: π × (hole radius)² × hole depth. For a typical 6ft fence with a 250mm wide hole at 700mm deep, that’s approximately 34 litres (0.034 m³) per post. A standard 20kg bag of post-mix concrete makes about 15–18 litres of set concrete. For a project-wide total, multiply per-post volume by number of posts and add 10% wastage.
The one-third rule states that the buried portion of a fence post should be at least one-third of the total post length. So a 2.4m post should be set at least 800mm into the ground, leaving 1.6m above ground. This ensures adequate leverage resistance against wind loads. For exposed, coastal, or high-wind locations, increasing burial depth to 40% of total length significantly improves stability.
Yes, significantly. In firm, well-drained loam or chalk, the standard one-third rule applies. In soft, sandy, or waterlogged ground, posts should be set 25–50% deeper and always set in concrete. Clay soils expand and contract with moisture changes, which can cause posts to lean over time — deeper holes with concrete collars that taper above ground level help prevent this. In rocky ground, you may need less depth but professional drilling equipment.
Concrete provides the strongest and most stable fixing for fence posts and is recommended for all wooden posts over 1.2m and any post carrying significant wind or lateral loads. Gravel or dry-pack filling can work for light decorative fencing in firm, free-draining soil, as it allows moisture to drain away from the post base and reduces rot. For maximum post life, treat all buried post sections with preservative and use gravel at the base under the concrete collar to improve drainage.
Post holes should be at least 2–3 times the width of the post. For a 75×75mm (3×3 inch) post, dig a hole at least 150–225mm (6–9 inches) wide. For a 100×100mm post, aim for 200–300mm. The wider the hole, the more concrete mass anchoring the post, which improves stability in soft ground. A post-hole borer (handheld or tractor-mounted) produces the cleanest, most consistent holes.
For a 6ft (1.8m) fence, you need posts that are at least 2.4m (8ft) long in good soil — this gives 1.8m above ground and 600mm in the ground. In softer soil where 900mm depth is needed, buy 2.7m posts. Always buy posts slightly longer than the calculation suggests, as you can trim them to a consistent height after installation but cannot add length to a post that is too short.
Standard fence panel spacing is 1.8m (6ft) centre-to-centre, as most fence panels in the UK are manufactured in this width. For close-board fencing, posts are typically spaced 1.8–3m apart. Gate posts must be spaced to match the gate width plus clearance for hinges and latches. In very exposed or high-wind locations, reducing post spacing to 1.5m significantly improves fence stability and resistance to storm damage.
