Fan Heater Running Cost Calculator
Instantly estimate how much your electric fan heater costs to run based on wattage, daily usage, and your specific energy tariff.
You can also work out the figures with our 3d print cost calculator.
Calculate Your Heater Running Cost
Enter your fan heater’s wattage, daily usage hours, and electricity rate below to get an instant, precise breakdown of your hourly, daily, monthly, and yearly running costs.
Heater Details
Enter your heater specifications and usage habits
Common sizes: 1000W, 2000W, 3000W
UK average is currently ~24p/kWh
Cost Breakdown
Based on your inputted usage and tariff
A Closer Look at the Fan Heater Running Cost Calculator In-Depth Notes
What this calculator does
Time is precious, and fan heater running cost should not eat into it. With the Fan Heater Running Cost Calculator, you can try several scenarios in a minute or two and compare the results side by side before you commit to anything.
Who it helps
This tool is useful for electronics hobbyists, landlords and facilities managers. Each group approaches fan heater running cost with different priorities, yet the same careful inputs lead to a result everyone can rely on. Many people open this page while choosing the right supply rating, checking a bill and comparing appliance efficiency. Having the answer ready keeps the rest of the task on track.
Getting accurate results
Preparation pays off here. Try to confirm your current tariff, then compare results across seasons. After that, enter the numbers in the Fan Heater Running Cost Calculator, read the answer, and repeat with a variation to test how stable the outcome really is.
Mistakes to avoid
Even careful users sometimes trip over ignoring power factor and efficiency, or end up skipping safety margins. Build a short pause into your routine to look for them, and your figures for fan heater running cost will hold up much better.
Reading your result
Treat the output as one piece of evidence rather than a final verdict. Think about how running and cost might change if your situation shifted, and repeat the calculation with updated values when it does. Because the calculation runs instantly in your browser, you can test as many scenarios as you like without any limit. Clear inputs lead to clear answers, so take a few extra seconds to read each label on the calculator before typing. Bookmark this page so the Fan Heater Running Cost Calculator is always one tap away when you need it again.
A note on accuracy
This Fan Heater Running Cost Calculator is a planning aid, not an installation guide. Electrical work should always be carried out or checked by a qualified electrician following current regulations.
Common Fan Heater Running Costs
Estimated costs based on a standard UK electricity rate of 24p per kWh. Actual costs may vary based on your specific tariff and thermostat cycling.
| Heater Wattage | Cost Per Hour | Cost Per Day (4 hrs) | Cost Per Month (30 days) | Energy Used Per Day |
|---|---|---|---|---|
| 1000W (1kW) | 24p | £0.96 | £28.80 | 4 kWh |
| 1500W (1.5kW) | 36p | £1.44 | £43.20 | 6 kWh |
| 2000W (2kW) | 48p | £1.92 | £57.60 | 8 kWh |
| 2500W (2.5kW) | 60p | £2.40 | £72.00 | 10 kWh |
| 3000W (3kW) | 72p | £2.88 | £86.40 | 12 kWh |
The Formula: Kilowatts Times Hours Times the Rate
Every running cost on this page comes from one formula. A fan heater’s size in kilowatts, multiplied by the hours it runs, gives the energy in kilowatt-hours; multiply that by your price per kilowatt-hour and you have the cost. A 2,000 W heater is 2 kW, so one hour uses 2 kWh. At the October to December 2026 price cap of 26.32p per kWh, that hour costs 2 × 26.32p = 52.6p. A 1,000 W heater costs 26.3p an hour, a 1,500 W heater costs 39.5p, and a 3,000 W heater costs 79.0p. The standing charge is separate: 54.83p a day at the same cap, whether you run a heater or not, which is £16.45 over a 30-day month. The calculator on this page applies the formula to any heater size and any hours you enter, so the tables below are worked examples at the cap rate — if your tariff is different, change the rate and the costs scale in proportion.
Cost by Wattage at the October to December 2026 Cap
The table gives the cost per hour, for an eight-hour day, and for eight hours a day over a 30-day month, at 26.32p per kWh. The pattern is exact: doubling the wattage doubles the cost, so the only decision that matters is how big a heater you run and for how long. A 750 W heater on low costs 19.7p an hour, £1.58 for an eight-hour day and £47.38 for the month. A 2 kW heater costs 52.6p an hour, £4.21 a day and £126.34 a month. A 3 kW heater costs 79.0p an hour, £6.32 a day and £189.50 a month. Those monthly figures assume the heater runs at full power for the whole eight hours, which it almost never does — that is where the thermostat comes in.
| Heater size | Cost per hour | Eight hours a day | Eight hours a day, 30 days |
|---|---|---|---|
| 750 W (low) | 19.7p | £1.58 | £47.38 |
| 1,000 W | 26.3p | £2.11 | £63.17 |
| 1,500 W | 39.5p | £3.16 | £94.75 |
| 2,000 W | 52.6p | £4.21 | £126.34 |
| 2,500 W | 65.8p | £5.26 | £157.92 |
| 3,000 W | 79.0p | £6.32 | £189.50 |
Thermostat Duty Cycle: Why the Heater Is Not Always On
A fan heater with a thermostat does not run at full power all the time. Once the room reaches the set temperature, the thermostat switches the heating element off and the fan keeps running, or the heater switches off entirely, and it only switches back on when the room cools. The duty cycle is the share of the time the element is actually heating: a 50% duty cycle means the heater is on for half the time and off for half, so it uses half the electricity of the full-power figure. A 2 kW heater at a 50% duty cycle costs 26.3p an hour, not 52.6p, because it is only drawing power for 30 minutes of each hour. At a 60% duty cycle it costs 31.6p an hour, and at 75% it costs 39.5p. The duty cycle depends on the room: a small, well-insulated room with the door closed may settle at 40 to 50%, while a draughty room or a heater set to maximum may run at 90% or more, barely switching off at all. That is why two households with the same heater can have very different bills — the thermostat setting and the room matter as much as the wattage. When you use the calculator, multiply the hours by your best guess at the duty cycle, or halve the answer for a heater that cycles on and off through the evening.
Two Heat Settings Compared: Low vs High
Most fan heaters have at least two heat settings, usually 1,000 W and 2,000 W, and the choice between them is a choice between speed and cost. On high, a 2 kW heater warms a cold room in about half the time of the 1 kW setting, but it costs exactly twice as much per hour: 52.6p against 26.3p. The cheapest way to use one is to run it on high until the room is warm, then drop to low and let the thermostat hold the temperature — the low setting then only tops up the heat the room loses, which is much less than the heat needed to warm it from cold. Worked out over an evening of four hours, high all evening costs £2.11, low all evening costs £1.05, and one hour on high followed by three hours on low costs 52.6p + 3 × 26.3p = £1.32 — nearly as cheap as low all evening, but with the room warm from the start. The worst option is high all evening in a room that is already warm, because the thermostat will cycle and you are paying for heat you do not need.
Preset Scenarios: An Evening, a Full Day and the Winter Season
Three scenarios cover most real use. An evening of four hours on a 2 kW heater at a 60% duty cycle uses 2 × 4 × 0.6 = 4.8 kWh and costs £1.26. A full eight-hour day on the same heater at 60% duty uses 9.6 kWh and costs £2.53. The winter season is where the numbers get serious: a 2 kW heater running six hours a day at a 60% duty cycle for 90 days uses 2 × 6 × 0.6 × 90 = 648 kWh and costs £170.55 at the cap rate. Run it at full power for those same six hours a day and the season costs £284.26. A smaller 1.5 kW heater running four hours a day at a 50% duty cycle for 90 days uses 270 kWh and costs £71.06 — less than half the 2 kW season figure, because both the size and the hours are smaller. The lesson is that the season cost is set by three numbers multiplied together — watts, hours and duty cycle — and cutting any one of them by a third cuts the bill by a third.
| Scenario | Heater | Hours a day | Duty cycle | Energy | Cost |
|---|---|---|---|---|---|
| One evening | 2 kW | 4 | 60% | 4.8 kWh | £1.26 |
| Full day | 2 kW | 8 | 60% | 9.6 kWh | £2.53 |
| Winter season, 90 days | 2 kW | 6 | 60% | 648 kWh | £170.55 |
| Winter season, 90 days, full power | 2 kW | 6 | 100% | 1,080 kWh | £284.26 |
| Winter season, 90 days | 1.5 kW | 4 | 50% | 270 kWh | £71.06 |
UK vs US Costs: Same Heater, Different Price
The same 2 kW heater costs different amounts on either side of the Atlantic, because the electricity price is different. In the UK at the October to December 2026 cap of 26.32p per kWh, one hour costs 52.6p, eight hours cost £4.21 and a 30-day month of eight-hour days costs £126.34. In the US, the Energy Information Administration projects the average residential price at 18.2 cents per kWh in 2026, so the same hour costs 36.4 cents, eight hours cost $2.91 and the month costs $87.36. The US average hides a wide spread: in August 2026 Hawaii averaged 47.18 cents per kWh and Nevada 12.72 cents, so the same 2 kW heater would cost 94.4 cents an hour in Hawaii and 25.4 cents an hour in Nevada. The formula is identical in both countries — kilowatts times hours times the rate — and the only thing that changes is the rate, so if you know your own price per kilowatt-hour you can work out your own cost from the UK table by scaling it.
| Heater size | UK cost per hour (26.32p/kWh) | US cost per hour (18.2¢/kWh) |
|---|---|---|
| 1,000 W | 26.3p | 18.2¢ |
| 1,500 W | 39.5p | 27.3¢ |
| 2,000 W | 52.6p | 36.4¢ |
| 2,500 W | 65.8p | 45.5¢ |
| 3,000 W | 79.0p | 54.6¢ |
Heater Types Compared: Fan, Oil-Filled, Halogen and Convector
Every electric heater turns almost 100% of the electricity it uses into heat, so no type is more efficient than another at the level of the plug — a 2 kW fan heater and a 2 kW oil-filled radiator both produce 2 kW of heat and both cost 52.6p an hour at the cap rate. What differs is how the heat reaches you. A fan heater blows warm air and heats a room fast, which makes it best for short bursts in a cold room, but it is noisy and the warmth fades quickly when it switches off. An oil-filled radiator heats slowly and stays warm after it switches off, which makes it best for background heat over hours, and it is silent. A halogen heater warms people rather than the room, which makes it best for one person sitting still, and a convector sits between the two — quieter than a fan heater, faster than oil. The running cost is set by the wattage and the hours, not by the type, so choose on comfort and noise, and use the calculator to work out what the hours will cost you.
| Heater type | Heats up | Best for | Noise | Cost per hour at 2 kW |
|---|---|---|---|---|
| Fan heater | Fast | Short bursts, cold rooms | Noisy | 52.6p |
| Oil-filled radiator | Slow | Background heat over hours | Silent | 52.6p |
| Halogen | Instant | One person, spot heating | Silent | 52.6p |
| Convector | Medium | Steady room heating | Quiet | 52.6p |
Does a fan heater cost more than central heating?
Usually yes per unit of heat. Gas costs roughly a quarter of electricity per kilowatt-hour, so heating a whole house with gas is much cheaper than heating it with electric heaters. A fan heater is best for one room for a short time.
How much does it cost to run a 2 kW fan heater all night?
Eight hours at full power costs £4.21 at the October to December 2026 cap of 26.32p per kWh. With the thermostat cycling at 60%, it costs about £2.53.
What is the cheapest heater setting?
The lowest wattage that keeps the room comfortable. Dropping from 2,000 W to 1,000 W halves the hourly cost from 52.6p to 26.3p, and the thermostat then does the rest.
Is the price cap the price I pay?
Not necessarily. The cap limits what suppliers can charge a typical household on a standard variable tariff. Fixed tariffs can be cheaper or dearer, and the cap itself changes every three months.
Related: work out freezer running cost, 3d print cost calculator.
Fan Heater Cost FAQ
Everything you need to know about calculating and reducing your electric fan heater running costs.
At the UK average electricity rate of 24p per kWh, a 2kW (2000W) fan heater costs approximately 48p per hour to run. This is calculated by multiplying the kilowatts (2kW) by the cost per kWh (24p).
To calculate the running cost: 1) Find the heater’s wattage (e.g., 2000W). 2) Divide by 1000 to get kilowatts (2kW). 3) Multiply by your electricity rate in pence per kWh (e.g., 24p). 4) Multiply by the number of hours used. For a 2kW heater used for 3 hours at 24p/kWh, the cost is 2 x 24 x 3 = 144p (£1.44).
Fan heaters are generally cheap to purchase but can be expensive to run for long periods because they use 100% of their rated wattage continuously when the thermostat is calling for heat. They are most cost-effective for short, targeted bursts of heat in small rooms rather than heating an entire house.
To reduce costs: use the heater’s thermostat to avoid overheating the room, only heat the room you are currently using, ensure doors and windows are closed to prevent drafts, and consider using a timer so it doesn’t run unnecessarily. Improving room insulation also significantly reduces heat loss.
